Download Price List
Products
Projects
Selector
 Download section
Primer DRYTEK PRIMER

DRYTEK® Primer contains acrylic polymers and deeply penetrating surface activation agents which maximize bond strength and reduce suction on most substrates. DRYTEK® Primer is multi-purpose - one product for all applications.

 
PERFORMANCE CHARACTERISTICS
Multi-purpose
Broom, roller or spray applied
Solvent Free, no VOC
For use on a wide range of substrates

DRYTEK PRIMER MIXING GUIDE

SUBSTRATE P:W* COVERAGE# APPLICATION
Concrete 1:3 400 SF Apply single coat of primer over entire substrate surface. Let dry prior to applying DRYTEK self-leveling product
Wood
Linoleum 		5:1 200 SF
       
NON-SUCTION: 1:1 285 SF Apply primer over entire susbtrate surface then lightly scatter DRYTEK self-leveling cement powder over the wet primer and broom to form a light slurry. Let slurry dry prior to applying DRYTEK self-leveling product. Slurry will dry within 1-4 hours depending on conditions.
Sheet Vinyl
Ceramic Tile
Quarry Tile
VCT/VAT
Epoxy
Urethane
Metal
Highly Burnished
Concrete 		   
       
HIGH-SUCTION: 1st coat
1:5		 200 SF Apply two coats of primer over entire substrate surface. Apply 1st coat at 1:5 (P:W ratio) and let dry before applying 2nd coat at 1:3 (P:W ratio). Let second coat dry prior to applying DRYTEK self-leveling product.
Highly Porous
Dry Substrates		 2nd coat
1:3 		 
       

Dilution Ratio - Primer:Water
#Coverage in square feet per gallon of concentrated primer.

 
DRYTEK® Primer can be spray, roller or broom applied
DRYTEK® PRIMER INSTRUCTIONS
spacer

CLEAN

Clean substrate to eliminate dust, dirt, oil, grease or any contaminants which may inhibit bonding. Mechanically clean weak or contaminated surfaces by shot blasting or scarifying. Do not use chemicals to clean the substrate without prior consent of a DRYTEK Representative.
spacer

CHECK CONDITIONS
Ensure substrate maintains minimum temperature of 50°F (10°C) during the application and the ambient temperature is maintained between 50-77°F (10-25°C) until dried.
spacer

MIX

Dilute with clean water according to the ratios given in the mixing guide table. Water amounts should be carefully measured to ensure proper mix ratio. Blend by hand with a mixing paddle.
spacer
PRIME
Apply DRYTEK® Primer with broom, roller, or spray - avoid puddling. Allow to become dry to touch. Maintain adequate ventilation during and after application. Note: DRYTEK® Primer is milky when wet and turns clear when dry.
spacer

PACKAGING
DRYTEK® Primer is available in one gallon jugs and five gallon pails.
spacer

STORAGE
DRYTEK® Primer should be stored in original packaging. Do not store at temperatures below freezing. Use within 12 months of date of manufacture.
spacer


Information contained on this website is not legally binding. Information contained herein is in good faith but Drytek Flooring Solutions Inc (DRYTEK) will not be held liable for information which has been misunderstood or used incorrectly. DRYTEK will not be held liable for improperly applied or used products, nor the specific use or pertinency of a product to a particular project. Information contained herein or otherwise administered by DRYTEK or its affiliates is based on the current and present knowledge of the products when used under normal circumstances and according to DRYTEK recommendations.

WARNING: Dust may cause skin, eye, nose, throat, or respiratory irritation. Avoid dust inhalation and exposure to dust. If dusty, wear a NIOSH/MSHA-approved dust respirator. Use proper ventilation to reduce dust exposure. Portland cement is strongly alkaline and can be corrosive to eyes, skin and respiratory tract. Wear eye and skin protection. If eye contact occurs, immediately flush thoroughly with water for 15 minutes and get medical attention. Do not ingest. If ingested and any discomfort occurs, call physician.